Vol. 6, No. 1, pp. 619-634 (2010)
INFLUENCE OF PARTIAL LOADING ON THE BEHAVIOUR OF PALLET
RACK STRUCTURES
F. Al Qarud 1, A. Shatnawi 1, M.S. Abdel-Jaber 1 and R.G. Beale 2,*
1 Department of Civil Engineering, University of Jordan, Amman, Jordan
2 Department of Mechanical Engineering, Wheatley Campus
Oxford Brookes University, Oxford, OX33 1HX, UK
*(Corresponding author: E-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.)
Received: 11 June 2008; Revised: 19 September 2008; Accepted: 22 September 2008
![]() |
Export Citation: Plain Text | RIS | Endnote |
ABSTRACT
This paper presents the results of an investigation into the effects of partial loading on the behaviour of steel pallet racks. A six level, six bay, 3-dimensional pallet rack frame model was built using ABAQUS and a geometrically non-linear analysis conducted. Twelve different load combinations were analysed under different boundary conditions and different side imperfections. Most combinations failed by sway buckling. Depending upon the side imperfection and the base condition critical combinations involved having completely unloaded bays or lifts adjacent to two or more fully loaded bays or lifts with reductions in capacity over a fully loaded rack of up to 40%.
KEYWORDS
Pallet rack structures, load combinations, pattern loading, semi-rigid connections, non-linear analysis, storage structures
REFERENCES
[1] Markazi, F.D., Godley, M.H.R. and Beale, R.G., “Experimental Analysis of Semi-Rigid Boltless connections”, Thin Walled Structures, 1997, Vol. 27, No. 1, pp. 53-87.
[2] Beale, R.G. and Godley, M.H.R. “Problems Arising with Pallet Rack Semi-rigid Base-plates”, Proceedings of the First International Conference on Steel and Composite Structures, Pusan, pp. 699-706.
[3] Godley, M.H.R. “The Behaviour of Storage Racking Baseplates”, Proceedings of the Sixth International Conference on Steel and Aluminium Structures (ICSAS’07), 2007, Oxford, pp.433-440.
[4] Baldassino, N. and Bernuzzi, C., “Analysis and Behaviour of Steel Storage Pallet Racks”, Thin-Walled Structures, 2000, Vol. 37, pp. 277-304.
[5] Abdel-Jaber, M.S., “The Influence of Semi-Rigid Connections on the Behaviour of Beam and Column Structural System”, PhD Thesis: Oxford Brookes University, UK, 2002.
[6] Sarawit, A.T. and Pekoz, T., “Design of Industrial Storage Racks”, Proceedings sixteenth International Specialty Conference on Cold-Formed Steel Structures”, Orlando, 2002, pp.369-384.
[7] Sarawit, A.T., “Cold-Formed Steel Frame and Beam-Column Design”, PhD Thesis: Cornell University, US, 2003.
[8] Freitas, A.M.S., Freitas, M.S.R. and Souza, F.T., “Analysis of Steel Storage Rack Columns”, Journal of Constructional Steel Research, 2005, Vol. 61, No. 8, pp. 1135-1146.
[9] Beale, R.G., “The Influence of Semi-Rigid Connections on the Non-Linear Behaviour of Pallet Rack and Scaffold Structures”. PhD Thesis: Oxford Brookes University, UK, 2004.
[10] Federation Europeéne de la Manutention, Section X, "Recommendations for the Design of Steel Pallet Racking and Shelving", 2000.
[11] The Rack Manufacturers’ Institute, “Specification for the Design, Testing and Utilization of Industrial Steel Storage Racks”, 1997.
[12] Beale, R.G. and Godley, M.H.R , “The Design of the Pallet Program”, Proceedings of the sixteenth Specialty Conference on Cold-Formed Steel Structures, Orlando, 2002, pp.353-368.
[13] Beale, R.G. and Godley, M.H.R., “Developments in the Pallet Program”, Advances in Structures, Sydney, 2003, pp. 237-243.
[14] Morz, K., Olsson, A. and Sandberg, G., "Parameter Studies on Pallet Racks", SP Swedish National Testing and Research Institute, SP Report 1998-2, 1998.
[15] Olsson, A. and Sandberg, G., “Reduction of Load Carrying Capacity in Pallet Racks due to Damaged Upright Beams”, Tenth Nordic Seminar on Computational Mechanics, Tallinn, 1997, pp. 278-281.
[16] ABAQUS ANALYSIS User’s Manual, Version 6.4, Hibbitt, Karlsson & Sorensen, Inc., 2003.